DG417BDJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Weight | 930.006106mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | DG417 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 89 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 80 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 89ns, 80ns |
| Charge Injection | 38pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 3.81mm |
| Length | 10.92mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG417BDJ-E3 Overview
Shipping overseas is convenient with the electronic component packed in 8-DIP (0.300, 7.62mm). A high level of reliability can be achieved through the use of an advanced packaging method Tube. Multiplexers like this are mounted in the Through Hole position. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~85°C TA. 8 terminations have been made so far. A 1 channel electronic part produces high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. There are 8 pins injected into the electronic part body. A SPST - NC switching circuit is used to build these analog multiplexers. The circuits in this analogue multiplexer number 1. Try searching for the analog switch ic with DG417 if you are looking for variants. This digital multiplexer has 35Ohm internal resistance. To find out what the 8 pins do, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 36V should not normally be supplied to the switches. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 13V is the lowest voltage that should be fed to the electronic electronic part. For this multiplexer to operate, 1μA current would be sufficient. Putting voltage greater than 1μA on the multiplexer may cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 22V. The voltage should be at least 7V if you are using dual power supplies. 20V operating voltages can be used with this electrical part.
DG417BDJ-E3 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
DG417BDJ-E3 Applications
There are a lot of Vishay Siliconix DG417BDJ-E3 Analog Switches & Multiplexers ICs applications.
- PCMCIA cards
- Avionics
- Intelligent PBX
- Sample-and-hold systems
- Switching Systems
- RGB switches
- Industrial
- ISDN NT1/TA
- Microwave transmission systems
- Avionics and Military Systems
