DG417BDY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 25Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 89 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 80 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 89ns, 80ns |
| Charge Injection | 38pC |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 35Ohm |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG417BDY Overview
Packed in 8-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. In total, there are 8 terminations. A electrical component with 1 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. As part of its design, the 8 series is equipped with this electronic component. A SPST - NC switching circuit is used to build these analog multiplexers. Circuits number 1 make up this analogue multiplexer. In this multiplexer, the internal resistance is 25Ohm. The datasheets for the 8 pins explain the functions. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. An effective Dual, Single supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 13V. A digital multiplexer may suffer damage if voltage is applied above 1μA. Despite this switch's dual supply capability, its voltage should not exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. The electronic component can function from 20V. Resistivity from Drain to Source is 35Ohm for this electronic part.
DG417BDY Features
1 Channels
Switch Circuit: SPST - NC
Drain-to-Source resistance: 35Ohm
DG417BDY Applications
There are a lot of Vishay Siliconix DG417BDY Analog Switches & Multiplexers ICs applications.
- PDH Multiplexers
- SONET/SDH ADM
- Avionics
- Industrial
- Relay Replacement
- Industrial and process control systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Transmit
- PBX interfaces
- RGB switches
