DG417BDY-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG417 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1nA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 89 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 80 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 89ns, 80ns |
| Charge Injection | 38pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG417BDY-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 8-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tube. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. In total, 8 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. This electronic part can be found in the 8 series. Unlike digital switches, these are based on SPST - NC switching circuits. Using the DG417 search parameter, you can discover variants of the switch. An switch multiplexer with 35Ohm internal resistance has a value of 35Ohm. The datasheets for the 8 pins explain the functions. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. Dual, Single supply type digital switch with a low cost. It is recommended to use 13V as the lowest voltage for the electrical part. For this multiplexer to operate, 1μA current would be sufficient. The analogue multiplexer may be damaged if voltage is greater than 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. It is recommended that you attach at least 7V to your dual power supply. Operating voltages of 20V are compatible with the electrical part. There are 1 inputs to be operated.
DG417BDY-E3 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
DG417BDY-E3 Applications
There are a lot of Vishay Siliconix DG417BDY-E3 Analog Switches & Multiplexers ICs applications.
- FTTH
- Medical systems
- Communication systems
- SDH
- Sample-and-hold systems
- DSUs
- Cross Connects
- Data switching
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Channel Banks
