DG417CJ
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG417 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG417CJ Overview
The electronic component is convenient to ship overseas because it is packed in a 8-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. Mounted in Through Hole is this multiplexer. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around 0°C~70°C TA. In total, there are 8 terminations. A 1 channel electronic part produces high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. 8 pins are injected to the electronic part body. Multiplexers built on a SPST - NC switching circuit are built. There are 1 circuits in this switch device. Try searching for DG417 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 35Ohm. Datasheets for functions of 8 pins are available. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 30V volts for the multiplexer. 10V is the lowest voltage the electrical component should receive. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. In the case of dual power supplies, you should connect at least 4.5V.
DG417CJ Features
1 Channels
Switch Circuit: SPST - NC
DG417CJ Applications
There are a lot of Maxim Integrated DG417CJ Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- PBX interfaces
- PDAs
- Video signal routing
- Low-Voltage
- PDH Multiplexers
- Data Acquisition Systems
- ATM
- Battery Powered Systems
- Fiber In The Loop (FITL)
