DG417DJ

175ns, 145ns SPST - NC 35Ohm Analog Switches BREAK-BEFORE-MAKE 8 Pins 250pA 8-DIP (0.300, 7.62mm)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG417DJ
Package: 8-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 999
Description: 175ns, 145ns SPST - NC 35Ohm Analog Switches BREAK-BEFORE-MAKE 8 Pins 250pA 8-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	8pF 8pF
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	175ns, 145ns
Charge Injection	60pC
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	20mOhm
Normal Position	NC
Height	3.81mm
Length	10.92mm
Width	7.11mm
RoHS Status	Non-RoHS Compliant
Factory Lead Time	1 Week
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	8-DIP (0.300, 7.62mm)
Number of Pins	8
Weight	930.006106mg
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2008
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Resistance	35Ohm
Terminal Finish	Tin/Lead (Sn/Pb)
Subcategory	Multiplexer or Switches
Max Power Dissipation	400mW
Technology	CMOS
Number of Functions	1
Terminal Pitch	2.54mm
Reach Compliance Code	unknown
Pin Count	8
Qualification Status	Not Qualified
Max Supply Voltage	36V
Min Supply Voltage	13V
Power Dissipation	400mW
Max Supply Current	1μA
Turn On Delay Time	175 ns
Number of Inputs	1
Voltage - Supply, Single/Dual (±)	12V ±15V
Supply Type	Dual, Single
Turn-Off Delay Time	145 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	35Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1

DG417DJ Overview

Packed in 8-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tube. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have the same number of circuits 1:1. Operational temperature extended around -40°C~85°C TA. Totally, there are 8 terminations. It is injected into the electrical part body with 8 pins. A SPST - NC switching circuit is used to build these analog multiplexers. A 35Ohm internal resistance characterizes this multiplexer. For functions related to 8 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. A voltage higher than 36V should not normally be supplied to the switches. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended that the electrical component receives a voltage of 13V. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. Despite this switch device's dual supply capability, its voltage should not exceed 22V. If you are using a dual power supply, you should attach at least 7V. Operating 1 inputs is required. There is 20mOhm resistance between the Drain and Source on this part.