DG417DY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1997 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 471mW |
| Base Part Number | DG417 |
| Pin Count | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Number of Bits | 2 |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG417DY Overview
As the electronic part is packed in 8-SOIC (0.154, 3.90mm Width), international shipping is convenient. To ensure high reliability, a new packaging method Tube is used. In Surface Mount, you'll find this switch device. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Increasing operating temperature to around -40°C~85°C TA. There are 8 pins injected into the electronic part body. Based on SPST - NC switching circuits, these analog multiplexers work. Circuits number 1 make up this analogue multiplexer. Search with DG417 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 100Ohm. You can find the functions of the 8 pins in the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 20V. The digital multiplexer has a low cost Dual, Single supply. The lowest voltage fed to the electronic component should be 4.5V. This digital switch can be operated with a current of 100pA. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. A dual power supply should have at least 4.5V voltage attached. It can conduct in a 2-bit manner.
DG417DY Features
Switch Circuit: SPST - NC
100pA Supply Current
2-Bit
DG417DY Applications
There are a lot of Maxim Integrated DG417DY Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- Digital cross connects (DSX-1)
- 65 V DACs
- Intelligent PBX
- Remote Powered Equipment
- Cable Modem
- DVD-R
- DSUs
- Avionics test equipment
- Cable Telephony – NIU, Set-Top Box, Home Side Box
