DG417DY-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 40Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG417 |
| Pin Count | 8 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1nA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 60pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Drain to Source Resistance | 20Ohm |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG417DY-E3 Overview
This electronic part is conveniently packaged in 8-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. Advanced packaging method Tube is used to provide high reliability. It is mounted in the position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature extended to -40°C~85°C TA. Total terminations are 8. Due to its 1 channels, the electrical component produces high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. There are 8 pins injected into the electronic part body. The analog switch ics are built using SPST - NC switching circuits. Search with DG417 if you are looking for analog multiplexer variants. As far as internal resistance is concerned, it has 40Ohm. For details about the functions of 8 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. A cost-effective Dual, Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 13V. This digital switch can be operated with a current of 1nA. A digital multiplexer may suffer damage if voltage is applied above 1μA. Despite this switch device's dual supply capability, its voltage should not exceed 22V. With dual power supplies, you should attach at least 7V. This electrical part is compatible with 15V operating voltages. There are 1 inputs to be operated. The Drain to Source resistance of this electronic component is 20Ohm.
DG417DY-E3 Features
1 Channels
Switch Circuit: SPST - NC
1nA Supply Current
Drain-to-Source resistance: 20Ohm
DG417DY-E3 Applications
There are a lot of Vishay Siliconix DG417DY-E3 Analog Switches & Multiplexers ICs applications.
- Multiplexers
- Central office
- T1/E1 Terminals
- Fault Tolerant Systems
- SONET/SDH ADM
- RGB switches
- Remote wireless modules
- Digital access cross connects
- Cable PC
- DSUs
