DG417DY-T1
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 35Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 60pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG417DY-T1 Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. 8 terminations have been made so far. A 1 channel electronic part produces high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. A total of 8 pins are injected into the body of the electronic part. A SPST - NC switching circuit is used for these analog switches. As far as internal resistance is concerned, it has 35Ohm. The datasheets for the 8 pins explain the functions. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage the electronic part should receive is 13V. Put voltage above 1μA on the multiplexer to cause damage. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. In the case of dual power supplies, you should connect at least 7V. There are 1 inputs to be operated.
DG417DY-T1 Features
1 Channels
Switch Circuit: SPST - NC
DG417DY-T1 Applications
There are a lot of Vishay Siliconix DG417DY-T1 Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Communication systems
- 65 V DACs
- HDTV
- ATM
- Signal routing between systems
- E1 Multiplexer
- Intelligent PBX
- Access Concentrators
- High reliability control systems
