DG417LDY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 20Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Pin Count | 8 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 41 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 32 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 20Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 43ns, 31ns |
| Charge Injection | 1pC |
| Crosstalk | -71dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 75ns |
| Drain to Source Resistance | 20Ohm |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG417LDY Overview
Shipping overseas is convenient due to the electrical component's packing in 8-SOIC (0.154, 3.90mm Width). Advanced packaging method Tube is used to provide high reliability. In Surface Mount, this analog switch is mounted. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. In total, there are 8 terminations. There are 8 pins injected into the electronic part body. A SPST - NC switching circuit is used for these analog switches. There is 20Ohm internal resistance in this digital multiplexer. Datasheets for functions of 8 pins are available. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 12V volts for the multiplexer. Dual, Single supply type digital switch with a low cost. A low voltage of 2.7V should be applied to the electronic component. When the digital multiplexer is charged above 1μA, damage can occur. Despite this switch's dual supply capability, its voltage should not exceed 6V. In the case of dual power supplies, you should connect at least 3V. In order to operate the 1 inputs, there are several steps to follow. Resistivity from Drain to Source is 20Ohm for this electronic part.
DG417LDY Features
Switch Circuit: SPST - NC
Drain-to-Source resistance: 20Ohm
DG417LDY Applications
There are a lot of Vishay Siliconix DG417LDY Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Data switching
- Industrial
- High reliability control systems
- Isolation
- Video signal routing
- Microprocessor controlled systems
- HDTV
- Precision data acquisition
- DSLAMs
