DG417LDY-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2013 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 18.5Ohm |
| Max Power Dissipation | 400mW |
| Base Part Number | DG417 |
| Pin Count | 8 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 41 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 32 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 20Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 43ns, 31ns |
| Charge Injection | 1pC |
| Crosstalk | -71dB @ 1MHz |
| Drain to Source Resistance | 20Ohm |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
DG417LDY-E3 Overview
This electronic part is conveniently packaged in 8-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. High reliability is ensured by the advanced packaging method Tube. It is mounted in the position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. A total of 8 pins are injected into the body of the electronic part. Unlike digital switches, these are based on SPST - NC switching circuits. Look for analog switch ic variants by searching with DG417. This digital multiplexer has 18.5Ohm internal resistance. The functions of 8 pins can be found in the datasheets. Users should never supply a voltage higher than 12V to a switch device. A cost-effective Dual, Single supply type analogue multiplexer. 2.7V is the lowest voltage that should be fed to the electronic electronic part. This digital switch can be operated with a current of 1μA. A voltage higher than 1μA may cause damage to the switch multiplexer. Despite this switch's dual supply capability, its voltage should not exceed 6V. A dual power supply should have at least 3V voltage attached. Operating 1 inputs is required. Drain to Source resistance for this electronic component is 20Ohm.
DG417LDY-E3 Features
Switch Circuit: SPST - NC
1μA Supply Current
Drain-to-Source resistance: 20Ohm
DG417LDY-E3 Applications
There are a lot of Vishay Siliconix DG417LDY-E3 Analog Switches & Multiplexers ICs applications.
- T1/E1 Terminals
- New designs requiring multiplexer functions
- FTTH
- Modems
- Cell phones
- Medical systems
- Cellular phones
- Microwave transmission systems
- Wireless Local Loop
- PBXs
