DG417LDY-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 20Ohm |
| Terminal Finish | MATTE TIN |
| Additional Feature | VIDEO APPLICATION |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | BICMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG417 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 41 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 2.7V~12V ±3V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 32 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 20Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 71 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 43ns, 31ns |
| Charge Injection | 1pC |
| Crosstalk | -71dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 44ns |
| Switch-off Time-Max | 33ns |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG417LDY-T1-E3 Overview
As the electronic part is packed in 8-SOIC (0.154, 3.90mm Width), international shipping is convenient. High reliability is provided by advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 8. This electronic part offers high-quality output due to its 1 channels. A 5V voltage supply should turn on and run the electronic component. The electronic part body is injected with 8 pins. Unlike digital switches, these are based on SPST - NC switching circuits. DG417 can be used to search for analog multiplexer variants. In this multiplexer, the internal resistance is 20Ohm. For functions related to 8 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 12V. The digital multiplexer has a low cost Dual, Single supply. It is recommended that the electrical component receives a voltage of 2.7V. An operating current of 1μA would be sufficient for this switch device. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. When using dual power supplies, you should attach at least 3V. Operating the 1 inputs requires 1 inputs. There is also VIDEO APPLICATION to look out for in this electronic part.
DG417LDY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
Additional Features: VIDEO APPLICATION
DG417LDY-T1-E3 Applications
There are a lot of Vishay Siliconix DG417LDY-T1-E3 Analog Switches & Multiplexers ICs applications.
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Avionics
- DSUs
- Avionics test equipment
- SDH/SONET multiplexers
- Power routing
- Intelligent PBX
- DVD-R
- Medical Instrumentation
- CSU
