DG417LDY+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | DG417L |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 26μA |
| Max Supply Current | 75μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 210 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 185ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG417LDY+T Overview
Packed in 8-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. 1:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~85°C TA. In total, there have been 8 terminations. A 1 channel electronic part produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. Based on SPST - NC switching circuits, these analog multiplexers work. The multiplexer consists of 1 circuits. Search with DG417L if you are looking for analog multiplexer variants. This digital multiplexer has 100Ohm internal resistance. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. Analog switch ics with Dual, Single supply type are cost-effective. 9V is the lowest voltage the electrical component should receive. If you put voltage higher than 75μA on the digital multiplexer, damage may occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. The electronic component can function from 18V.
DG417LDY+T Features
1 Channels
Switch Circuit: SPST - NC
DG417LDY+T Applications
There are a lot of Maxim Integrated DG417LDY+T Analog Switches & Multiplexers ICs applications.
- Avionics
- Battery Powered Systems
- Digital cross connects (DSX-1)
- SONET/SDH ADM
- ISDN NT1/TA
- Voice over IP/DSL – Integrated Access Devices, Smart
- Digital Cross-Connects
- PDAs
- Sample hold systems
- Transmit
