DG417LEUA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 362mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | DG417 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 26μA |
| Max Supply Current | 26μA |
| Number of Bits | 2 |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 185 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 185ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG417LEUA+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). This high-reliability packaging method uses advanced packaging methods Tube. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature around -40°C~85°C TA extended. The total number of terminations is 8. The electronic part provides high-quality output because it has 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. The electrical component body receives 8 pins. A SPST - NC switching circuit is used for these analog switches. The multiplexer consists of 1 circuits. Try searching with DG417 to find analog multiplexer variants. The internal resistance of this digital multiplexer is 100Ohm. For details about the functions of 8 pins, please refer to the datasheets. Multiplexers should not be powered above 36V in normal situations. Analogue multiplexer with a Dual, Single supply type that is cost-effective. The lowest voltage the electronic part should receive is 9V. The switch multiplexer may be damaged if it is exposed to voltage greater than 26μA. Despite this switch device's dual supply capability, its voltage should not exceed 20V. For dual power supplies, a voltage of at least 4.5V should be attached. Operating voltages of 20V are compatible with the electrical part. It conducts in a 2-bit manner.
DG417LEUA+ Features
1 Channels
Switch Circuit: SPST - NC
2-Bit
DG417LEUA+ Applications
There are a lot of Maxim Integrated DG417LEUA+ Analog Switches & Multiplexers ICs applications.
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Digital Cross-Connects
- Optical Applications
- Imaging
- Data Acquisition Systems
- Channel Banks
- Frame Relay Equipment
- Multiplexers
- PBXs
- Industrial control systems
