DG417LEUA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 362mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | DG417L |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 26μA |
| Max Supply Current | 75μA |
| Number of Bits | 2 |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 210 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 185ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG417LEUA+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operational temperature extended around -40°C~85°C TA. Total terminations are 8. A electrical component with 1 channels is capable of high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An electrical component of this type can be found in the 8 series. Based on SPST - NC switching circuits, these analog multiplexers work. There are 1 circuits in this multiplexer. Search with DG417L if you are looking for analog multiplexer variants. In this multiplexer, the internal resistance is 100Ohm. You can find the functions of the 8 pins in the datasheets. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. The digital multiplexer has a low cost Dual, Single supply. The lowest voltage the electronic part should receive is 9V. If put voltage greater than 75μA on the device, damage may be caused to the analogue multiplexer. There is no problem with using dual supply voltage, but it should not exceed 20V. If you are using dual power supplies, you should attach at least 4.5V. 18V operating voltages are supported by the electronic component. It is able to conduct in a 2-bit way.
DG417LEUA+T Features
1 Channels
Switch Circuit: SPST - NC
2-Bit
DG417LEUA+T Applications
There are a lot of Maxim Integrated DG417LEUA+T Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Audio and video switching
- E1 Network Equipment
- Cable Modem
- Wireless Local Loop
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Voice over IP/DSL – Integrated Access Devices, Smart
- Industrial
- Signal routing between systems
- Fiber In The Loop (FITL)
