DG418AK/883B
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 8-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Operating Supply Voltage | 28V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Max Supply Current | 1μA |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 18V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Normal Position | NO |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG418AK/883B Overview
This electronic part is conveniently packaged in 8-CDIP (0.300, 7.62mm), making it easy to ship abroad. A high level of reliability can be achieved through the use of an advanced packaging method Tube. This analog switch is mounted in Through Hole. 1:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -55°C~125°C TA. Total terminations are 8. The electronic part provides high-quality output because it has 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. This electrical component is included in the 8 series of products. On the other hand, analog switches can be constructed using SPST - NO switching circuits. The multiplexer consists of 1 circuits. The internal resistance of this digital multiplexer is 35Ohm. The functions of 8 pins can be found in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 30V. A analog switch ic that has a cost-effective Dual, Single supply type. The lowest voltage fed to the electronic component should be 10V. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. If you are using a dual power supply, you should attach at least 4.5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. 28V operating voltages are supported by the electronic component.
DG418AK/883B Features
1 Channels
Switch Circuit: SPST - NO
DG418AK/883B Applications
There are a lot of Maxim Integrated DG418AK/883B Analog Switches & Multiplexers ICs applications.
- PDH Multiplexers
- FTTH
- MP3 players
- E1 Network Equipment
- 65 V DACs
- E1 Multiplexer
- Avionics
- Intelligent PBX
- Battery-powered systems
- PBX interfaces
