DG418BDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Weight | 930.006106mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 25Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | DG418 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 89 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 80 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 89ns, 80ns |
| Charge Injection | 38pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 99ns |
| Normal Position | NC |
| Height | 3.81mm |
| Length | 10.92mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG418BDJ Overview
The electrical component comes in 8-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tube. In Through Hole, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. Extended operating temperature around -40°C~85°C TA. 8 terminations have been made so far. A electrical component with 1 channels is capable of high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. The electronic part body is injected with 8 pins. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Using the DG418 search parameter, you can discover variants of the switch. It has an internal resistance of 25Ohm. Datasheets for functions of 8 pins are available. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 36V. Digital switch that provides Dual, Single power at a cost-effective price. The lowest voltage the electronic part should receive is 13V. When the digital multiplexer is charged above 1μA, damage can occur. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. The voltage should be at least 7V if you are using dual power supplies. There is a voltage range of 20V operating voltages for the electrical part. Among the inputs that can be operated are the 1 inputs.
DG418BDJ Features
1 Channels
Switch Circuit: SPST - NO
DG418BDJ Applications
There are a lot of Vishay Siliconix DG418BDJ Analog Switches & Multiplexers ICs applications.
- Public switching systems
- Audio and video routing
- USB 1.1 signal switching circuits
- SONET
- Fiber to the Home
- PCMCIA cards
- ISDN NT1/TA
- Channel Banks
- PBXs
- Sample hold systems
