DG418BDJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Weight | 930.006106mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | DG418 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 89 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 80 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 89ns, 80ns |
| Charge Injection | 38pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 99ns |
| Normal Position | NO |
| Height | 3.81mm |
| Length | 10.92mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG418BDJ-E3 Overview
The electrical component comes in 8-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tube. In Through Hole, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 1:1. The operating temperature is extended to around -40°C~85°C TA. In total, there are 8 terminations. By its 1 channels, the electronic component provides high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. This electronic part can be found in the 8 series. A SPST - NO switching circuit is used to build these analog multiplexers. The circuits in this analogue multiplexer number 1. Search with DG418 if you are looking for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 35Ohm. To find out what the functions of 8 pins are, please refer to their datasheets. It is a typical Multiplexer or Switches analog multiplexer. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. The digital multiplexer has a low cost Dual, Single supply. A low voltage of 13V should be applied to the electronic component. 1μA current would be enough for this multiplexer to operate. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. Despite this switch device's dual supply capability, its voltage should not exceed 22V. If you are using a dual power supply, you should attach at least 7V. Operating voltages of 20V are compatible with the electrical part.
DG418BDJ-E3 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
DG418BDJ-E3 Applications
There are a lot of Vishay Siliconix DG418BDJ-E3 Analog Switches & Multiplexers ICs applications.
- DSLAMs
- Avionics and Military Systems
- T1/E1 Terminals
- Wireless Local Loop
- Sample-and-hold systems
- SDH
- Industrial control systems
- USB 1.1 signal switching circuits
- Private Branch Exchange (PBX)
- DSUs
