DG418BDQ-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Number of Pins | 8 |
| Weight | 139.989945mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG418 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | -20V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 89 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 80 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 89ns, 80ns |
| Charge Injection | 38pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 99ns |
| Normal Position | NO |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG418BDQ-T1-E3 Overview
Due to its 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there are 8 terminations. High-quality output is provided by the electronic component's 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An electrical component like this is included in the 8 series. Based on SPST - NO switching circuits, these analog multiplexers work. A total of 1 circuits make up this switch device. Look for analog switch ic variants by searching with DG418. This digital multiplexer has 35Ohm internal resistance. To find out what the 8 pins do, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 20V to the switch device in normal circumstances. Digital switch that provides Dual, Single power at a cost-effective price. The lowest voltage fed to the electronic component should be -20V. It would be sufficient to run this analogue multiplexer with 1μA current. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. Despite this switch device's dual supply capability, its voltage should not exceed 22V. If you are using a dual power supply, you should attach at least 7V.
DG418BDQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
DG418BDQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG418BDQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Communications systems
- Sample hold systems
- Cell phones
- PCMCIA cards
- Switching Systems
- Industrial
- ATM
- Imaging
- Audio signal routing
- Low-Voltage
