DG418BDY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 25Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 89 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 80 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 89ns, 80ns |
| Charge Injection | 38pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 99ns |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG418BDY Overview
Shipping overseas is convenient due to the electrical component's packing in 8-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tube. It is mounted in the position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. In total, 8 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. A total of 8 pins are injected into the body of the electronic part. These analog multiplexers are built based on SPST - NO switching circuits. In this multiplexer, the internal resistance is 25Ohm. The functions of 8 pins can be found in the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Users shouldn't supply more than 36V voltage to the switch device. Dual, Single supply type digital switch with a low cost. It is recommended that the electrical component receives a voltage of 13V. When the digital multiplexer is charged above 1μA, damage can occur. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. 20V operating voltages are supported by the electronic component. Operating the 1 inputs requires 1 inputs.
DG418BDY Features
1 Channels
Switch Circuit: SPST - NO
DG418BDY Applications
There are a lot of Vishay Siliconix DG418BDY Analog Switches & Multiplexers ICs applications.
- Power routing
- Precision instrumentation
- Cellular phones
- Private Branch Exchange (PBX)
- Cable Modem
- Automatic test equipment
- Audio and video routing
- Audio and video signal routing
- Medical systems
- USB 1.1 signal switching circuits
