DG418BDY-E3
| Parameters | |
|---|---|
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG418 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1nA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 89 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 80 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 89ns, 80ns |
| Charge Injection | 38pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 99ns |
| Normal Position | NO |
| Height | 1.55mm |
DG418BDY-E3 Overview
Presented in 8-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tube is used. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a ratio of 1:1. Operational temperature extended around -40°C~85°C TA. In total, there have been 8 terminations. This electronic part offers high-quality output due to its 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. A total of 8 pins are injected into the body of the electronic part. Circuits based on SPST - NO switching are used to construct these analog switch ics. If you are looking for variants of the digital switch, trying search with DG418. The internal resistance of this digital multiplexer is 35Ohm. The functions of 8 pins can be found in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. Digital switch that provides Dual, Single power at a cost-effective price. The lowest voltage fed to the electronic component should be 13V. This multiplexer would work with 1μA current. A voltage higher than 1μA may cause damage to the switch multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. In the case of dual power supplies, you should connect at least 7V. Operating voltages range from 20V. It is possible to operate 1 inputs.
DG418BDY-E3 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
DG418BDY-E3 Applications
There are a lot of Vishay Siliconix DG418BDY-E3 Analog Switches & Multiplexers ICs applications.
- FTTH
- Precision test equipment
- Remote wireless modules
- Channel Banks
- Avionics and Military Systems
- Residential Gateways, Home Gateway/Router
- Switching Systems
- Central office
- Modems
- SDH
