Parameters |
Width |
4mm |
RoHS Status |
Non-RoHS Compliant |
Factory Lead Time |
1 Week |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Weight |
540.001716mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
Resistance |
25Ohm |
Terminal Finish |
TIN LEAD |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
400mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
15V |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
30 |
Pin Count |
8 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
20V |
Number of Channels |
1 |
Number of Circuits |
1 |
Max Supply Voltage |
36V |
Min Supply Voltage |
13V |
Max Supply Current |
1μA |
Turn On Delay Time |
89 ns |
Voltage - Supply, Single/Dual (±) |
12V ±15V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
80 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
25Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
82 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
89ns, 80ns |
Charge Injection |
38pC |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
99ns |
Normal Position |
NO |
Height |
1.55mm |
Length |
5mm |
DG418BDY-T1 Overview
This electronic part is conveniently packaged in 8-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature around -40°C~85°C TA extended. A total of 8 terminations have been recorded. High-quality output is provided by the electronic component's 1 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. Into the electrical component body are injected 8 pins. Based on SPST - NO switching circuits, these analog multiplexers work. The circuits in this analogue multiplexer number 1. In this multiplexer, the internal resistance is 25Ohm. To find out what the functions of 8 pins are, please refer to their datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. The analog switch ic is of the Dual, Single supply type and is cost-effective. There should be 13V voltage fed to the electrical part below 13V. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. For this switch, a dual supply voltage is feasible, but it must not exceed 22VWhen using dual power supplies, you should attach at least 7V. A voltage of 20V can be used to operate the electronic component.
DG418BDY-T1 Features
1 Channels
Switch Circuit: SPST - NO
DG418BDY-T1 Applications
There are a lot of Vishay Siliconix DG418BDY-T1 Analog Switches & Multiplexers ICs applications.
- Optical Applications
- Audio and video switching
- Data Acquisition Systems
- HDTV
- Relay replacements
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Cross Connects
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Low-Voltage
- Remote wireless modules