DG418CJ
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1997 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Max Power Dissipation | 727mW |
| Base Part Number | DG418 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG418CJ Overview
Shipping overseas is convenient due to the electrical component's packing in 8-DIP (0.300, 7.62mm). High reliability is ensured by the advanced packaging method Tube. This analog switch is mounted in Through Hole. Multiplexer and demultiplexer circuits have a number 1:1. Increasing operating temperature to around 0°C~70°C TA. A key feature of the 8 series is the inclusion of this electronic part as part of its design. These analog multiplexers are built based on SPST - NO switching circuits. It consists of 1 circuits. Try searching for the analog switch ic with DG418 if you are looking for variants. As far as internal resistance is concerned, it has 35Ohm. To find out what the functions of 8 pins are, please refer to their datasheets. A voltage higher than 30V should not normally be supplied to the switches. An effective Dual, Single supply digital multiplexer. The lowest voltage fed to the electronic component should be 10V. The analogue multiplexer could operate on 100pA current. Putting voltage greater than 1μA on the multiplexer may cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 20VIn the case of dual power supplies, you should connect at least 4.5V. The electrical part can be operated at 18V voltage levels.
DG418CJ Features
Switch Circuit: SPST - NO
100pA Supply Current
DG418CJ Applications
There are a lot of Maxim Integrated DG418CJ Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- USB 1.1 signal switching circuits
- Industrial and process control systems
- Cell phones
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Optical Applications
- Medical
- Data Acquisition Systems
- Fiber to the Home
- Communication systems
