DG418CY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1997 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Max Power Dissipation | 471mW |
| Base Part Number | DG418 |
| Pin Count | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Number of Bits | 2 |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG418CY Overview
This electronic part is conveniently packaged in 8-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tube. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. An extended operating temperature of 0°C~70°C TA degrees Celsius. An electrical component of this type can be found in the 8 series. Unlike digital switches, these are based on SPST - NO switching circuits. A total of 1 circuits make up this switch device. DG418 can be used to search for analog multiplexer variants. It has an internal resistance of 100Ohm. For details about the functions of 8 pins, please refer to the datasheets. Users should never supply a voltage higher than 20V to a switch device. Dual, Single supply type digital switch with a low cost. 4.5V is the lowest voltage the electrical component should receive. The analogue multiplexer could operate on 100pA current. When the digital multiplexer is charged above 1μA, damage can occur. There is no problem with using dual supply voltage, but it should not exceed 20V. A dual power supply should have at least 4.5V voltage attached. It can conduct 2-bit signals.
DG418CY Features
Switch Circuit: SPST - NO
100pA Supply Current
2-Bit
DG418CY Applications
There are a lot of Maxim Integrated DG418CY Analog Switches & Multiplexers ICs applications.
- Multiplexers
- Ultrasound
- High speed data transmission line cards
- Remote Powered Equipment
- Cable PC
- FTTH
- Automotive applications
- DVD-R
- Low-Voltage
- SONET
