DG418DJ
| Parameters | |
|---|---|
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | DG418 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Through Hole |
DG418DJ Overview
As the electronic part is packed in 8-DIP (0.300, 7.62mm), international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tube. Mounted in Through Hole is this multiplexer. Multiplexers and demultiplexers have a number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 8. The electronic part delivers high-quality output through its 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. As part of its design, the 8 series is equipped with this electronic component. Unlike digital switches, these are based on SPST - NO switching circuits. A 1 circuit is present in this switch device. Look for analog switch ic variants by searching with DG418. The internal resistance of this digital multiplexer is 35Ohm. Datasheets for functions of 8 pins are available. This switch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. It is recommended to use 10V as the lowest voltage for the electrical part. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply.
DG418DJ Features
1 Channels
Switch Circuit: SPST - NO
DG418DJ Applications
There are a lot of Maxim Integrated DG418DJ Analog Switches & Multiplexers ICs applications.
- Mechanical reed relay replacement
- RGB switches
- Communication systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Industrial and process control systems
- Low-Voltage
- CSU
- SDH
- Multi-Line E1 Interface Cards
- Video signal routing
