DG418DJ
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Weight | 930.006106mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Number of Functions | 1 |
| Terminal Pitch | 2.54mm |
| Pin Count | 8 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 60pC |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height | 3.81mm |
| Length | 10.92mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG418DJ Overview
Presented in 8-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. To ensure high reliability, a new packaging method Tube is used. In Through Hole, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 1:1. Operating temperature extended to -40°C~85°C TA. 8 terminations have been made so far. The electronic part body is injected with 8 pins. Multiplexers built on a SPST - NO switching circuit are built. An switch multiplexer with 35Ohm internal resistance has a value of 35Ohm. The functions of 8 pins can be found in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. A cost-effective Dual, Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 13V. The analogue multiplexer may be damaged if voltage is greater than 1μA. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. If you are using dual power supplies, you should attach at least 7V. Operating 1 inputs is required.
DG418DJ Features
Switch Circuit: SPST - NO
DG418DJ Applications
There are a lot of Vishay Siliconix DG418DJ Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- CSU
- Digital access cross connects
- Audio signal routing
- Multi-Line E1 Interface Cards
- Battery Powered Systems
- SDH
- PBX interfaces
- 65 V DACs
- MP3 players
