DG418DJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Weight | 930.006106mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG418 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1nA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 60pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Drain to Source Resistance | 35Ohm |
| Normal Position | NO |
| Height | 3.81mm |
| Length | 10.92mm |
| Width | 7.11mm |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG418DJ-E3 Overview
Packed in 8-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tube is used. It is mounted in the position Through Hole. There is 1:1 ratio between the number of multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. A total of 8 terminations have been recorded. The electronic part delivers high-quality output through its 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. As part of the design of the 8 series, this electronic part has been incorporated into the system. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching with DG418 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 35Ohm. Please refer to the datasheets for 8 pins functions. There is Multiplexer or Switches analog multiplexer like this in the world. normally, users should not supply switches with voltages higher than 36V. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 13V. This multiplexer would work with 1nA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. There is no problem with using dual supply voltage, but it should not exceed 22V. With dual power supplies, you should attach at least 7V. This electrical part is compatible with 15V operating voltages. A 1 input needs to be operated. There is 35Ohm resistance between the Drain and Source on this part.
DG418DJ-E3 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
Drain-to-Source resistance: 35Ohm
DG418DJ-E3 Applications
There are a lot of Vishay Siliconix DG418DJ-E3 Analog Switches & Multiplexers ICs applications.
- Cable PC
- PBXs
- PDH Multiplexers
- Cable Modem
- Medical
- Switching Systems
- Battery-powered systems
- Imaging
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Communications systems
