Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-SOIC (0.154, 3.90mm Width) |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
1997 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
100Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
471mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG418 |
Pin Count |
8 |
Operating Supply Voltage |
20V |
Number of Channels |
1 |
Number of Circuits |
1 |
Max Supply Voltage |
30V |
Min Supply Voltage |
10V |
Nominal Supply Current |
-100pA |
Max Supply Current |
-100pA |
Number of Bits |
2 |
Throw Configuration |
SPST |
Turn On Delay Time |
175 ns |
Voltage - Supply, Single/Dual (±) |
10V~30V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
145 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
8pF 8pF |
On-state Resistance Match-Nom |
3Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
175ns, 145ns |
Charge Injection |
3pC |
Channel-to-Channel Matching (ΔRon) |
3 Ω (Max) |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Height |
1.5mm |
Length |
5mm |
Width |
4mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG418DY+ Overview
As the electronic part is packed in 8-SOIC (0.154, 3.90mm Width), international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tube. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 1:1. Extended operating temperature around -40°C~85°C TA. In total, there are 8 terminations. High-quality output is provided by the electronic component's 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. The analog switch ics are built using SPST - NO switching circuits. There are 1 circuits in this switch device. Try searching with DG418 if you're looking for variants. It has an internal resistance of 100Ohm. For functions related to 8 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 30V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended that the electrical component receives a voltage of 10V. The analogue multiplexer may be damaged if voltage is greater than -100pA. There is no problem with using dual supply voltage, but it should not exceed 20V. When using dual power supplies, you should attach at least 4.5V. 20V operating voltages are supported by the electronic component. It can conduct 2-bit signals.
DG418DY+ Features
1 Channels
Switch Circuit: SPST - NO
2-Bit
DG418DY+ Applications
There are a lot of Maxim Integrated DG418DY+ Analog Switches & Multiplexers ICs applications.
- PBXs
- Microwave transmission systems
- Private Branch Exchange (PBX)
- PBX interfaces
- Industrial
- Audio/video switches
- Communication systems
- Communications systems
- SDH/SONET multiplexers
- Signal routing between systems