DG418DY
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Pin Count | 8 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 30mA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Number of Bits | 2 |
| Turn On Delay Time | 175 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 60pC |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 20mOhm |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
DG418DY Overview
Shipping overseas is convenient due to the electrical component's packing in 8-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tube is used. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature around -40°C~85°C TA extended. In total, there have been 8 terminations. An injection of 8 pins is performed into the body of the electrical component. SPST - NO switching circuits are used in these analog switch ics. A 35Ohm internal resistance characterizes this multiplexer. For details about the functions of 8 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 36V. A analog switch ic that has a cost-effective Dual, Single supply type. 13V is the lowest voltage that should be fed to the electronic electronic part. This multiplexer would work with 30mA current. A digital multiplexer may suffer damage if voltage is applied above 1μA. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. When using dual power supplies, you should attach at least 7V. In order to operate the 1 inputs, there are several steps to follow. There is 20mOhm resistance between the Drain and Source on this part. 2-bit conductivity is possible.
DG418DY Features
Switch Circuit: SPST - NO
30mA Supply Current
Drain-to-Source resistance: 20mOhm
2-Bit
DG418DY Applications
There are a lot of Vishay Siliconix DG418DY Analog Switches & Multiplexers ICs applications.
- PCMCIA cards
- Intelligent PBX
- Wireless Local Loop
- DVD-R
- Communications systems
- Audio and video routing
- Optical Applications
- Remote wireless modules
- Imaging
- Data switching
