DG418DY-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 265 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG418 |
| Pin Count | 8 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1nA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 60pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Drain to Source Resistance | 20mOhm |
| Normal Position | NO |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG418DY-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 8-SOIC (0.154, 3.90mm Width). High reliability is ensured by the advanced packaging method Tube. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operating temperature extended to -40°C~85°C TA. There are 8 terminations totally. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. Electronic part bodies are injected with 8 pins. Multiplexers built on a SPST - NO switching circuit are built. Using the DG418 search parameter, you can discover variants of the switch. There is 35Ohm internal resistance in this digital multiplexer. Datasheets for 8 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. In a normalsituation, users should not supply the switches with voltage higher than 36V. A analog switch ic that has a cost-effective Dual, Single supply type. There should be 13V voltage fed to the electrical part below 13V. An operating current of 1nA would be sufficient for this switch device. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. There is no problem with using dual supply voltage, but it should not exceed 22V. A dual power supply should have at least 7V voltage attached. This electrical part is compatible with 15V operating voltages. It is possible to operate 1 inputs. There is 20mOhm Drain to Source resistance on this electronic part.
DG418DY-E3 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
Drain-to-Source resistance: 20mOhm
DG418DY-E3 Applications
There are a lot of Vishay Siliconix DG418DY-E3 Analog Switches & Multiplexers ICs applications.
- Medical Instrumentation
- PDAs
- Intelligent PBX
- Cable PC
- Precision data acquisition
- Fiber In The Loop (FITL)
- Communications systems
- SDH
- DVD-R
- Microwave transmission systems
