DG418DY-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 40Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG418 |
| Pin Count | 8 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1nA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 60pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Normal Position | NC |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG418DY-T1-E3 Overview
Shipping overseas is convenient due to the electrical component's packing in 8-SOIC (0.154, 3.90mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 1:1. Temperatures around -40°C~85°C TA are extended for operation. A total of 8 terminations have been recorded. The electronic part delivers high-quality output through its 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. It is injected into the electrical part body with 8 pins. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Look for analog switch ic variants by searching with DG418. The internal resistance of this digital multiplexer is 40Ohm. For functions related to 8 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. Analog switch ics with Dual, Single supply type are cost-effective. 13V is the lowest voltage that should be fed to the electronic electronic part. The switch device would be able to operate with 1nA current. Put voltage above 1μA on the multiplexer to cause damage. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. If you are using a dual power supply, you should attach at least 7V. The electronic component can function from 15V. The 1 inputs need to be operated in order to work.
DG418DY-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
DG418DY-T1-E3 Applications
There are a lot of Vishay Siliconix DG418DY-T1-E3 Analog Switches & Multiplexers ICs applications.
- Central office
- Digital Cross-Connects
- HDTV
- Communications systems
- Battery-powered systems
- MP3 players
- Precision test equipment
- Signal routing between systems
- Channelized and Unchannelized DS3 applications
- Public switching systems
