DG418LDY+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG418L |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | +-4.5/+-20/9/36V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| On-State Resistance (Max) | 35Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 185ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
DG418LDY+ Overview
Shipping overseas is convenient due to the electrical component's packing in 8-SOIC (0.154, 3.90mm Width). The advanced packaging method Tube provides high reliability. A switch device like this is mounted in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~85°C TA. A total of 8 terminations have been recorded. The electronic part delivers high-quality output through its 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. This electronic part can be found in the 8 series. A SPST - NO switching circuit is used to build these analog multiplexers. The circuits in this analogue multiplexer number 1. DG418L can be used to search for analog multiplexer variants. For details about the functions of 8 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches.
DG418LDY+ Features
1 Channels
Switch Circuit: SPST - NO
DG418LDY+ Applications
There are a lot of Maxim Integrated DG418LDY+ Analog Switches & Multiplexers ICs applications.
- DSLAMs
- Mechanical reed relay replacement
- Battery Powered Systems
- Signal routing between systems
- ISDN NT1/TA
- Switching Systems
- Channelized and Unchannelized DS3 applications
- Cable PC
- Relay replacements
- Wireless Local Loop
