DG418LDY+T
| Parameters | |
|---|---|
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG418 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 26μA |
| Max Supply Current | 75μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 210 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 185ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
DG418LDY+T Overview
Shipping overseas is convenient with the electronic component packed in 8-SOIC (0.154, 3.90mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. 8 terminations have been made so far. The electronic part delivers high-quality output through its 1 channels. With a 15V voltage supply, the electrical component should be turned on and run. The electrical component body receives 8 pins. Multiplexers built on a SPST - NO switching circuit are built. The circuits in this analogue multiplexer number 1. Try searching for DG418 variants of the analog switch ic. Analog switches have 100Ohm internal resistance. The analogue multiplexer in this example is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 36V. Digital switch that provides Dual, Single power at a cost-effective price. 9V should be the lowest voltage fed to the electronic component. If put voltage greater than 75μA on the device, damage may be caused to the analogue multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. A dual power supply should have at least 4.5V voltage attached. The electrical part can be operated at 18V voltage levels.
DG418LDY+T Features
1 Channels
Switch Circuit: SPST - NO
DG418LDY+T Applications
There are a lot of Maxim Integrated DG418LDY+T Analog Switches & Multiplexers ICs applications.
- Audio/video switches
- DSUs
- USB 1.1 signal switching circuits
- Residential Gateways, Home Gateway/Router
- Avionics test equipment
- Wireless Local Loop
- Multi-Line E1 Interface Cards
- Private Branch Exchange (PBX)
- Medical
- Cable Telephony – NIU, Set-Top Box, Home Side Box
