DG418LEUA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 362mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | DG418 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 26μA |
| Max Supply Current | 26μA |
| Number of Bits | 2 |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 185 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 185ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Height | 950μm |
| Length | 3.05mm |
| Width | 3.05mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG418LEUA+ Overview
The electronic component is convenient to ship overseas because it is packed in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). Advanced packaging method Tube is used to provide high reliability. Mounted in Surface Mount is this multiplexer. 1:1 is the number of circuits in the multiplexer and demultiplexer. Around -40°C~85°C TA is the extended operating temperature. In total, 8 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. Electronic part bodies are injected with 8 pins. Unlike digital switches, these are based on SPST - NO switching circuits. There are 1 circuits in this multiplexer. Use DG418 to search for variants of the digital switches. Analog switches have 100Ohm internal resistance. Datasheets for 8 pin functions are available upon request. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. The analog switch ic is of the Dual, Single supply type and is cost-effective. 9V is the lowest voltage the electrical component should receive. A digital multiplexer may suffer damage if voltage is applied above 26μA. For this switch, a dual supply voltage is feasible, but it must not exceed 20VIn the case of dual power supplies, you should connect at least 4.5V. Operating voltages range from 20V. The switch device is capable of conducting in a 2-bit mode.
DG418LEUA+ Features
1 Channels
Switch Circuit: SPST - NO
2-Bit
DG418LEUA+ Applications
There are a lot of Maxim Integrated DG418LEUA+ Analog Switches & Multiplexers ICs applications.
- T1/E1 Terminals
- Audio signal routing
- FTTH
- Isolation
- Video switching
- Digital cross connects (DSX-1)
- DVD-R
- DSLAMs
- Transmit
- Power routing
