DG418LEUA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 362mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | DG418L |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 9V |
| Nominal Supply Current | 26μA |
| Max Supply Current | 75μA |
| Number of Bits | 2 |
| Throw Configuration | SPST |
| Turn On Delay Time | 300 ns |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 210 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 185ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG418LEUA+T Overview
As the electronic part is packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), international shipping is convenient. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. This analog switch is mounted in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 8. By its 1 channels, the electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An electrical component like this is included in the 8 series. On the other hand, analog switches can be constructed using SPST - NO switching circuits. This multiplexer is composed of 1 circuits. Try searching with DG418L if you're looking for variants. The internal resistance of this digital multiplexer is 100Ohm. You can find the functions of the 8 pins in the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 36V. Analog switch ics with Dual, Single supply type are cost-effective. There should be 9V voltage fed to the electrical part below 9V. A digital multiplexer may suffer damage if voltage is applied above 75μA. There is no problem with using dual supply voltage, but it should not exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply. 18V operating voltages can be used with this electrical part. Its conductivity is 2-bit.
DG418LEUA+T Features
1 Channels
Switch Circuit: SPST - NO
2-Bit
DG418LEUA+T Applications
There are a lot of Maxim Integrated DG418LEUA+T Analog Switches & Multiplexers ICs applications.
- Automotive applications
- Sample-and-hold systems
- Channel Banks
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- New designs requiring multiplexer functions
- Communication systems
- PBX interfaces
- High speed data transmission line cards
- Modems
- Audio signal routing
