DG419AK/883B
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 8-CDIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 30Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Operating Supply Voltage | 28V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Max Supply Current | 1μA |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 30Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 18V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG419AK/883B Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-CDIP (0.300, 7.62mm). A high level of reliability can be achieved through the use of an advanced packaging method Tube. The multiplexer is located in Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operational temperature extended around -55°C~125°C TA. 8 terminations have been made so far. A electrical component with 1 channels is capable of high-quality output. A 15V voltage supply should turn on and run the electronic component. A key feature of the 8 series is the inclusion of this electronic part as part of its design. A SPDT switching circuit is used for these analog switches. This multiplexer is composed of 1 circuits. It has an internal resistance of 30Ohm. To find out what the functions of 8 pins are, please refer to their datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. A analog switch ic that has a cost-effective Dual, Single supply type. 10V is the lowest voltage that should be fed to the electronic electronic part. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. Despite this switch device's dual supply capability, its voltage should not exceed 20V. If you are using dual power supplies, you should attach at least 4.5V. This analog switch ic utilizes SEPARATE OUTPUT output. Operating voltages range from 28V.
DG419AK/883B Features
1 Channels
Switch Circuit: SPDT
DG419AK/883B Applications
There are a lot of Maxim Integrated DG419AK/883B Analog Switches & Multiplexers ICs applications.
- Residential Gateways, Home Gateway/Router
- Modems
- Mechanical reed relay replacement
- ISDN NT1/TA
- Automotive applications
- Avionics test equipment
- Battery Powered Systems
- High reliability control systems
- Private Branch Exchange (PBX)
- PDH Multiplexers
