DG419BDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Weight | 930.006106mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 25Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 89 ns |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 80 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 89ns, 80ns |
| Charge Injection | 38pC |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 35Ohm |
| Normal Position | NO/NC |
| Height | 3.81mm |
| Length | 10.92mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
DG419BDJ Overview
The electrical component comes in 8-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. Advanced packaging method Tube is used to provide high reliability. Mounted in Through Hole is this multiplexer. Multiplexer and demultiplexer circuits have a number 2:1. Operating temperature extended to -40°C~85°C TA. Totally, there are 8 terminations. The electronic part delivers high-quality output through its 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. A total of 8 pins are injected into the body of the electronic part. The analog switch ics are built using SPDT switching circuits. It consists of 1 circuits. The internal resistance of this digital multiplexer is 25Ohm. To find out what the 8 pins do, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Dual, Single supply type digital switch with a low cost. A low voltage of 13V should be applied to the electronic component. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. It is recommended that you attach at least 7V to your dual power supply. Operating voltages of 20V are compatible with the electrical part. A Drain to Source resistance of 35Ohm is shown for this electronic part.
DG419BDJ Features
1 Channels
Switch Circuit: SPDT
Drain-to-Source resistance: 35Ohm
DG419BDJ Applications
There are a lot of Vishay Siliconix DG419BDJ Analog Switches & Multiplexers ICs applications.
- DSUs
- Avionics and Military Systems
- Channel Banks
- DSLAMs
- Transmit
- Wireless Local Loop
- USB 1.1 signal switching circuits
- Intelligent PBX
- ISDN NT1/TA
- Existing multiplexer applications (both fault-protected and nonfault-protected)
