banner_page

DG419BDJ-E3

89ns, 80ns SPDT 25Ohm Analog Switches BREAK-BEFORE-MAKE DG419 8 Pins 250pA 15V 8-DIP (0.300, 7.62mm)


  • Manufacturer: Vishay Siliconix
  • Nocochips NO: 880-DG419BDJ-E3
  • Package: 8-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 417
  • Description: 89ns, 80ns SPDT 25Ohm Analog Switches BREAK-BEFORE-MAKE DG419 8 Pins 250pA 15V 8-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Base Part Number DG419
Pin Count 8
Operating Supply Voltage 20V
Number of Channels 1
Number of Circuits 1
Max Supply Voltage 36V
Min Supply Voltage 13V
Operating Supply Current 1μA
Max Supply Current 1μA
Turn On Delay Time 89 ns
Voltage - Supply, Single/Dual (±) 12V ±15V
Supply Type Dual, Single
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 80 ns
Max Dual Supply Voltage 22V
On-State Resistance (Max) 25Ohm
Min Dual Supply Voltage 7V
Dual Supply Voltage 15V
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 82 dB
Current - Leakage (IS(off)) (Max) 250pA
Channel Capacitance (CS(off), CD(off)) 12pF 12pF
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 89ns, 80ns
Charge Injection 38pC
Crosstalk -88dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Height 3.81mm
Length 10.92mm
Width 7.11mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Factory Lead Time 1 Week
Mount Through Hole
Mounting Type Through Hole
Package / Case 8-DIP (0.300, 7.62mm)
Number of Pins 8
Weight 930.006106mg
Operating Temperature -40°C~85°C TA
Packaging Tube
Published 2016
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
Resistance 35Ohm
Terminal Finish Matte Tin (Sn)
Subcategory Multiplexer or Switches
Max Power Dissipation 400mW
Technology CMOS
Number of Functions 4
Supply Voltage 15V
Terminal Pitch 2.54mm

DG419BDJ-E3 Overview


Shipping overseas is convenient due to the electrical component's packing in 8-DIP (0.300, 7.62mm). This packaging method provides high reliability because it uses advanced packaging techniques. In Through Hole, you'll find this switch device. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. The operating temperature is extended to around -40°C~85°C TA. In total, there have been 8 terminations. A high-quality output is provided by the electrical component's 1 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. There is an electrical component included in the 8 series. Multiplexers built on a SPDT switching circuit are built. A total of 1 circuits make up this switch device. DG419 can be used to search for analog multiplexer variants. This digital multiplexer has 35Ohm internal resistance. To find out what the functions of 8 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 36V. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended that the electrical component receives a voltage of 13V. The analogue multiplexer could operate on 1μA current. A digital multiplexer may suffer damage if voltage is applied above 1μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. Operating voltages range from 20V.

DG419BDJ-E3 Features


1 Channels
Switch Circuit: SPDT
1μA Supply Current

DG419BDJ-E3 Applications


There are a lot of Vishay Siliconix DG419BDJ-E3 Analog Switches & Multiplexers ICs applications.

  • Microprocessor Controlled Analog Systems
  • Automatic test equipment
  • Relay Replacement
  • PBX interfaces
  • Fiber to the Home
  • Precision instrumentation
  • Imaging
  • Cable PC
  • Isolation
  • High-Voltage

Write a review

Note: HTML is not translated!
    Bad           Good