DG419BDQ-T1-E3
| Parameters | |
|---|---|
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount, Through Hole |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Number of Pins | 8 |
| Supplier Device Package | 8-MSOP |
| Weight | 139.989945mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 35Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 400mW |
| Base Part Number | DG419 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 15V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPDT |
| Turn On Delay Time | 89 ns |
| Number of Inputs | 2 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 80 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 7V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 89ns, 80ns |
| Charge Injection | 38pC |
| Crosstalk | -88dB @ 1MHz |
| Drain to Source Resistance | 35Ohm |
DG419BDQ-T1-E3 Overview
Shipping overseas is convenient with the electronic component packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Extended operating temperature around -40°C~85°C TA. The electronic part delivers high-quality output through its 1 channels. Circuits based on SPDT switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 1. Try searching with DG419 if you're looking for variants. It has an internal resistance of 35Ohm. You can find the functions of the 8 pins in the datasheets. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. Analog switch ics with Dual, Single supply type are cost-effective. 13V is the lowest voltage the electrical component should receive. For this multiplexer to operate, 1μA current would be sufficient. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. In the case of dual power supplies, you should connect at least 7V. This electrical part is compatible with 15V operating voltages. It is possible to operate 2 inputs. Temperatures over 85°C should not be allowed for the multiplexer to operate. This electronic component presents a Drain to Source resistance of 35Ohm. The analog switch ics includes 2 outputs. There is a 8-MSOP package available from suppliers.
DG419BDQ-T1-E3 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
Drain-to-Source resistance: 35Ohm
DG419BDQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG419BDQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Channel Banks
- Audio signal routing
- SDH/SONET multiplexers
- Multi-Line E1 Interface Cards
- PCMCIA cards
- MP3 players
- Communications systems
- Automatic test equipment
- Optical Applications
