DG419BDY
| Parameters | |
|---|---|
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2016 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 25Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 89 ns |
| Number of Inputs | 2 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 80 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 25Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 89ns, 80ns |
| Charge Injection | 38pC |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO/NC |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
DG419BDY Overview
Shipping overseas is convenient due to the electrical component's packing in 8-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. In Surface Mount, this analog switch is mounted. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Extended operating temperature around -40°C~85°C TA. Total terminations are 8. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. An electrical component like this is included in the 8 series. Unlike digital switches, these are based on SPDT switching circuits. The multiplexer consists of 1 circuits. There is 25Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 8 pins functions. A analogue multiplexer of this type is a Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. A analog switch ic that has a cost-effective Dual, Single supply type. 13V is the lowest voltage the electrical component should receive. A voltage higher than 1μA may cause damage to the switch multiplexer. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. When using dual power supplies, you should attach at least 7V. It can operate from 20V operating voltages. The 2 inputs need to be operated in order to work.
DG419BDY Features
1 Channels
Switch Circuit: SPDT
DG419BDY Applications
There are a lot of Vishay Siliconix DG419BDY Analog Switches & Multiplexers ICs applications.
- Audio signal routing
- DSLAMs
- Mechanical reed relay replacement
- Relay Replacement
- Microprocessor controlled systems
- PCMCIA cards
- Ultrasound
- High-Voltage
- Communication systems
- Industrial control systems
