DG419BDY-T1

89ns, 80ns SPDT 25Ohm Analog Switches BREAK-BEFORE-MAKE 8 Pins 250pA 15V 8-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG419BDY-T1
Package: 8-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 656
Description: 89ns, 80ns SPDT 25Ohm Analog Switches BREAK-BEFORE-MAKE 8 Pins 250pA 15V 8-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	8-SOIC (0.154, 3.90mm Width)
Number of Pins	8
Weight	540.001716mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2009
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Resistance	25Ohm
Terminal Finish	TIN LEAD
Subcategory	Multiplexer or Switches
Max Power Dissipation	400mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	240
Number of Functions	4
Supply Voltage	15V
Time@Peak Reflow Temperature-Max (s)	30
Pin Count	8
Operating Supply Voltage	20V
Number of Channels	1
Number of Circuits	1
Max Supply Voltage	36V
Min Supply Voltage	13V
Power Dissipation	400mW
Max Supply Current	1μA
Turn On Delay Time	89 ns
Number of Inputs	2
Voltage - Supply, Single/Dual (±)	12V ±15V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	80 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	25Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	82 dB
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	12pF 12pF
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	89ns, 80ns
Charge Injection	38pC
Crosstalk	-88dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Height	1.55mm
Length	5mm
Width	4mm
Radiation Hardening	No
RoHS Status	Non-RoHS Compliant

DG419BDY-T1 Overview

Shipping overseas is convenient due to the electrical component's packing in 8-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature around -40°C~85°C TA extended. Totally, there are 8 terminations. A high-quality output is provided by the electrical component's 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. The electrical component body receives 8 pins. Multiplexers built on a SPDT switching circuit are built. There are 1 circuits in this multiplexer. Internally, this switch multiplexer has a resistance of 25Ohm. For functions related to 8 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 36V should not normally be supplied to the switches. Analogue multiplexers of the Dual, Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 13V. When the digital multiplexer is charged above 1μA, damage can occur. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. When using dual power supplies, you should attach at least 7V. It can operate from 20V operating voltages. Among the inputs that can be operated are the 2 inputs.