DG419CJ+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | DG419 |
| Pin Count | 8 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 100pA |
| Nominal Supply Current | -100pA |
| Max Supply Current | -100pA |
| Turn On Delay Time | 100 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 4.45mm |
| Length | 9.91mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG419CJ+ Overview
Shipping overseas is convenient with the electronic component packed in 8-DIP (0.300, 7.62mm). Advanced packaging method Tube is used to provide high reliability. Mounted in Through Hole is this multiplexer. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Temperatures around 0°C~70°C TA are extended for operation. In total, there have been 8 terminations. The electronic part delivers high-quality output through its 1 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. An electrical component like this is included in the 8 series. These analog multiplexers are built based on SPDT switching circuits. Try searching with DG419 to find analog multiplexer variants. There is 100Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 8 pins functions. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 30V in normal situations. Digital switch that provides Dual, Single power at a cost-effective price. It is recommended that the electrical component receives a voltage of 10V. 100pA current would be enough for this multiplexer to operate. When the digital multiplexer is charged above -100pA, damage can occur. For this switch, a dual supply voltage is feasible, but it must not exceed 20VIf you are using a dual power supply, you should attach at least 4.5V. This electrical part is compatible with 20V operating voltages.
DG419CJ+ Features
1 Channels
Switch Circuit: SPDT
100pA Supply Current
DG419CJ+ Applications
There are a lot of Maxim Integrated DG419CJ+ Analog Switches & Multiplexers ICs applications.
- Ultrasound
- Battery Powered Systems
- Microwave transmission systems
- Multi-Line E1 Interface Cards
- Avionics test equipment
- SONET
- Frame Relay Equipment
- Microprocessor Controlled Analog Systems
- Channelized and Unchannelized DS3 applications
- Central office
