DG419CY+
| Parameters | |
|---|---|
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG419 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 100pA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 35Ohm |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 506.605978mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
DG419CY+ Overview
Presented in 8-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Extended operating temperature around 0°C~70°C TA. Total terminations are 8. A 1 channel electronic part produces high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. A key feature of the 8 series is the inclusion of this electronic part as part of its design. On the other hand, analog switches can be constructed using SPDT switching circuits. Using the DG419 search parameter, you can discover variants of the switch. This digital multiplexer has 35Ohm internal resistance. To find out what the functions of 8 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 30V should not normally be supplied to the switches. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 10V voltage fed to the electrical part below 10V. For this digital switch to work, 100pA current would suffice. A digital multiplexer may suffer damage if voltage is applied above 1μA. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. The voltage should be at least 4.5V if you are using dual power supplies. Drain to Source resistance for this electronic component is 35Ohm.
DG419CY+ Features
1 Channels
Switch Circuit: SPDT
100pA Supply Current
Drain-to-Source resistance: 35Ohm
DG419CY+ Applications
There are a lot of Maxim Integrated DG419CY+ Analog Switches & Multiplexers ICs applications.
- Mechanical reed relay replacement
- Microprocessor Controlled Analog Systems
- Ultrasound
- Fiber to the Home
- Automotive applications
- High reliability control systems
- Microwave transmission systems
- Cable PC
- Audio/video switches
- PBXs
