DG419DJ+

175ns, 145ns SPDT 35Ohm Analog Switches BREAK-BEFORE-MAKE DG419 8 Pins 250pA 15V 8-DIP (0.300, 7.62mm)

Manufacturer: Maxim Integrated
Nocochips NO: 503-DG419DJ+
Package: 8-DIP (0.300, 7.62mm)
Datasheet: PDF
Stock: 739
Description: 175ns, 145ns SPDT 35Ohm Analog Switches BREAK-BEFORE-MAKE DG419 8 Pins 250pA 15V 8-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Through Hole
Mounting Type	Through Hole
Package / Case	8-DIP (0.300, 7.62mm)
Number of Pins	8
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	1997
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
ECCN Code	EAR99
Resistance	35Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	727mW
Technology	CMOS
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	15V
Terminal Pitch	2.54mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	DG419
Pin Count	8
Operating Supply Voltage	20V
Number of Channels	1
Max Supply Voltage	30V
Min Supply Voltage	10V
Operating Supply Current	100pA
Nominal Supply Current	-100pA
Max Supply Current	-100pA
Turn On Delay Time	175 ns
Voltage - Supply, Single/Dual (±)	10V~30V ±4.5V~20V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	145 ns
Max Dual Supply Voltage	20V
On-State Resistance (Max)	35Ohm
Min Dual Supply Voltage	4.5V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	68 dB
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	8pF 8pF
On-state Resistance Match-Nom	3Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	175ns, 145ns
Charge Injection	3pC
Channel-to-Channel Matching (ΔRon)	3 Ω (Max)
Crosstalk	-85dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Height Seated (Max)	4.572mm
Length	9.375mm
Width	7.62mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG419DJ+ Overview

Due to its 8-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tube is used. Through Hole is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 2:1. Operational temperature extended around -40°C~85°C TA. Totally, there are 8 terminations. The electronic part delivers high-quality output through its 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. An electrical component of this type can be found in the 8 series. SPDT switching circuits are used in these analog switch ics. Look for analog switch ic variants by searching with DG419. The internal resistance of this digital multiplexer is 35Ohm. The datasheets for the 8 pins explain the functions. This switch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 30V. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage the electronic part should receive is 10V. It would be sufficient to run this analogue multiplexer with 100pA current. Putting voltage greater than -100pA on the multiplexer may cause damage. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 20V. A dual power supply should have at least 4.5V voltage attached. A voltage of 20V can be used to operate the electronic component.