DG419DY+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 506.605978mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 100Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 471mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG419 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Operating Supply Current | 100pA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG419DY+ Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, you'll find this switch device. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. 8 terminations have been made so far. This electronic part offers high-quality output due to its 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. A total of 8 pins are injected into the electrical part body. The analog switch ics are built using SPDT switching circuits. Search with DG419 if you are looking for analog multiplexer variants. As far as internal resistance is concerned, it has 100Ohm. To find out what the functions of 8 pins are, please refer to their datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 30V in normal situations. Dual, Single supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 10V. For this digital switch to work, 100pA current would suffice. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. Despite this switch's dual supply capability, its voltage should not exceed 20V. With dual power supplies, you should attach at least 4.5V.
DG419DY+ Features
1 Channels
Switch Circuit: SPDT
100pA Supply Current
DG419DY+ Applications
There are a lot of Maxim Integrated DG419DY+ Analog Switches & Multiplexers ICs applications.
- Data switching
- Cable Modem
- Communication systems
- Channelized and Unchannelized DS3 applications
- Frame Relay Equipment
- Precision instrumentation
- Cellular phones
- E1 Multiplexer
- Data Acquisition Systems
- Audio and video routing
