DG419DY
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 30mA |
| Nominal Supply Current | 1nA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 60pC |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 35Ohm |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
DG419DY Overview
As the electronic part is packed in 8-SOIC (0.154, 3.90mm Width), international shipping is convenient. Advanced packaging method Tube is used to provide high reliability. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a number of circuits 2:1. Increasing operating temperature to around -40°C~85°C TA. 8 terminations have been made so far. A total of 8 pins are injected into the body of the electronic part. Multiplexers built on a SPDT switching circuit are built. This digital multiplexer has 35Ohm internal resistance. For details about the functions of 8 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 36V volts for the multiplexer. Analogue multiplexer with a Dual, Single supply type that is cost-effective. A low voltage of 13V should be applied to the electronic component. It would be sufficient to run this analogue multiplexer with 30mA current. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. There is no problem with using dual supply voltage, but it should not exceed 22V. The voltage should be at least 7V if you are using dual power supplies. There are 1 inputs to be operated. Drain to Source resistance for this electronic component is 35Ohm. An output of 2 is provided by the digital multiplexer.
DG419DY Features
Switch Circuit: SPDT
30mA Supply Current
Drain-to-Source resistance: 35Ohm
DG419DY Applications
There are a lot of Vishay Siliconix DG419DY Analog Switches & Multiplexers ICs applications.
- Battery Powered Instruments
- E1 Network Equipment
- Routers
- High speed data transmission line cards
- DSUs
- Medical
- Channel Banks
- Microprocessor controlled systems
- Precision test equipment
- Fault Tolerant Systems
