DG419DY-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 540.001716mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 400mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG419 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1nA |
| Power Dissipation | 400mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPDT, SPST |
| Turn On Delay Time | 175 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 60pC |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 40Ohm |
| Height | 1.55mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG419DY-T1-E3 Overview
Shipping overseas is convenient due to the electrical component's packing in 8-SOIC (0.154, 3.90mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. The operating temperature is extended to around -40°C~85°C TA. A total of 8 terminations have been recorded. Due to its 1 channels, the electrical component produces high-quality output. A 15V voltage supply should turn on and run the electronic component. The electrical component body receives 8 pins. Based on SPDT switching circuits, these analog multiplexers work. Try searching for DG419 variants of the analog switch ic. This digital multiplexer has 35Ohm internal resistance. To find out what the 8 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. The digital multiplexer has a low cost Dual, Single supply. It is recommended that the electrical component receives a voltage of 13V. In order to operate this switch device, it would need a current of 1nA. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. It is recommended that you attach at least 7V to your dual power supply. It can operate from 15V operating voltages. There are 1 inputs to be operated. The Drain to Source resistance of this electronic component is 40Ohm. In this digital multiplexer, there are 2 outputs.
DG419DY-T1-E3 Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
Drain-to-Source resistance: 40Ohm
DG419DY-T1-E3 Applications
There are a lot of Vishay Siliconix DG419DY-T1-E3 Analog Switches & Multiplexers ICs applications.
- PBXs
- Relay replacements
- Cable PC
- Industrial and process control systems
- Medical systems
- RGB switches
- PCMCIA cards
- Battery Powered Systems
- Microwave transmission systems
- DSLAMs
