DG419LDQ-T1-E3

43ns, 31ns SPDT 20Ohm Analog Switches BREAK-BEFORE-MAKE DG419 8 Pins 1nA 5V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG419LDQ-T1-E3
Package: 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad
Datasheet: PDF
Stock: 477
Description: 43ns, 31ns SPDT 20Ohm Analog Switches BREAK-BEFORE-MAKE DG419 8 Pins 1nA 5V 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad(Kg)

Inquiry Now

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad
Number of Pins	8
Weight	139.989945mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2014
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	8
Resistance	20Ohm
Terminal Finish	Matte Tin (Sn)
Additional Feature	VIDEO APPLICATION
Subcategory	Multiplexer or Switches
Max Power Dissipation	320mW
Technology	BICMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	5V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG419
Pin Count	8
Number of Outputs	2
Number of Channels	1
Voltage	5V
Max Supply Voltage	12V
Min Supply Voltage	2.7V
Operating Supply Current	1μA
Nominal Supply Current	20nA
Power Dissipation	320mW
Max Supply Current	1μA
Turn On Delay Time	41 ns
Number of Inputs	1
Voltage - Supply, Single/Dual (±)	2.7V~12V ±3V~6V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	32 ns
Max Dual Supply Voltage	6V
On-State Resistance (Max)	20Ohm
Min Dual Supply Voltage	3V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	71 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	5pF
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	43ns, 31ns
Charge Injection	1pC
Crosstalk	-71dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	44ns
Switch-off Time-Max	33ns
Drain to Source Resistance	35Ohm
Height	850μm
Length	3mm
Width	3mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG419LDQ-T1-E3 Overview

The electrical component comes in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad packaging, which makes it convenient to ship overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 8. The electronic part provides high-quality output because it has 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. A total of 8 pins are injected into the body of the electronic part. A SPDT switching circuit is used for these analog switches. Look for analog switch ic variants by searching with DG419. As far as internal resistance is concerned, it has 20Ohm. For details about the functions of 8 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. An abnormal situation would be for the switch device to be supplied with a voltage greater than 12V. A cost-effective Dual, Single supply type analogue multiplexer. 2.7V should be the lowest voltage fed to the electronic component. 1μA current would be enough for this multiplexer to operate. The analogue multiplexer may be damaged if voltage is greater than 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. A dual power supply should have at least 3V voltage attached. The electrical component supports 1 inputs. Check out the electrical component's additional features, such as the following: VIDEO APPLICATION. Drain to Source resistance is 35Ohm. Multiplexer ics with 2 outputs are available.