DG428DN
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-LCC (J-Lead) |
| Number of Pins | 20 |
| Supplier Device Package | 20-PLCC (9x9) |
| Weight | 722.005655mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 100Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 800mW |
| Number of Outputs | 1 |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Power Dissipation | 800mW |
| Max Supply Current | 100μA |
| Propagation Delay | 250 ns |
| Turn On Delay Time | 300 ns |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 7V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 40pF |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 5Ohm |
| Drain to Source Resistance | 100Ohm |
| Height | 3.69mm |
| Length | 9.04mm |
| Width | 9.04mm |
| RoHS Status | Non-RoHS Compliant |
DG428DN Overview
As the electronic part is packed in 20-LCC (J-Lead), international shipping is convenient. High reliability is achieved by using advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. 8:1 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~85°C TA. A 8 channel electronic part produces high-quality output. A total of 1 circuits make up this switch device. Internally, this switch multiplexer has a resistance of 100Ohm. You can find the functions of the 20 pins in the datasheets. In normalcircumstances, users should not exceed 36V volts for the multiplexer. An effective Dual, Single supply digital multiplexer. 13V is the lowest voltage that should be fed to the electronic electronic part. Putting voltage greater than 100μA on the multiplexer may cause damage. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. The voltage should be at least 7V if you are using dual power supplies. It is possible to operate 8 inputs. It is not recommended to operate the switches in an environment with a temperature higher than 85°C. This electronic component presents a Drain to Source resistance of 100Ohm. The analogue multiplexer has 1 outputs. It is offered by suppliers in package 20-PLCC (9x9).
DG428DN Features
8 Channels
Drain-to-Source resistance: 100Ohm
DG428DN Applications
There are a lot of Vishay Siliconix DG428DN Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- ISDN NT1/TA
- Communications systems
- Precision data acquisition
- Battery Powered Systems
- PDAs
- E1 Network Equipment
- Sample hold systems
- Medical
