DG428DN-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-LCC (J-Lead) |
| Number of Pins | 20 |
| Weight | 722.005655mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Resistance | 150Ohm |
| Max Power Dissipation | 800mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG428 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 20μA |
| Power Dissipation | 800mW |
| Max Supply Current | 100μA |
| Propagation Delay | 250 ns |
| Turn On Delay Time | 300 ns |
| Logic Function | Multiplexer |
| Max Input Voltage | 44V |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 7V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 40pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 225ns |
| Signal Current-Max | 0.03A |
| Height | 3.69mm |
| Length | 9.04mm |
| Width | 9.04mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
DG428DN-E3 Overview
Shipping overseas is convenient with the electronic component packed in 20-LCC (J-Lead). In order to provide high reliability, an advanced packaging method Tube is used. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 8:1. Operational temperature extended around -40°C~85°C TA. In total, there are 20 terminations. High-quality output is provided by the electronic component's 8 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. The electronic part body is injected with 20 pins. A 1 circuit is present in this switch device. Use DG428 to search for variants of the digital switches. Internally, this switch multiplexer has a resistance of 150Ohm. To find out what the functions of 20 pins are, please refer to their datasheets. An abnormal situation would be for the switch device to be supplied with a voltage greater than 36V. Analog switch ics with Dual, Single supply type are cost-effective. 13V should be the lowest voltage fed to the electronic component. This multiplexer would work with 20μA current. It may damage the digital multiplexer if the voltage is higher than 100μA. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. A dual power supply should have at least 7V voltage attached.
DG428DN-E3 Features
8 Channels
20μA Supply Current
DG428DN-E3 Applications
There are a lot of Vishay Siliconix DG428DN-E3 Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- PBX interfaces
- Medical systems
- Battery Powered Instruments
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Communications systems
- Industrial
- Wireless Local Loop
- Sample-and-hold systems
- Multiplexers
