DG429DJ-E3
| Parameters | |
|---|---|
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 18 |
| Resistance | 150Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | DG429 |
| Pin Count | 18 |
| Number of Channels | 4 |
| Leakage Current | 1μA |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 100μA |
| Power Dissipation | 470mW |
| Max Supply Current | 100μA |
| Propagation Delay | 250 ns |
| Turn On Delay Time | 300 ns |
| Logic Function | Multiplexer |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 12V ±15V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 100Ohm |
| Min Dual Supply Voltage | 7V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 11pF 20pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 150ns, 150ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.03A |
| Length | 37.4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 18-DIP (0.300, 7.62mm) |
| Number of Pins | 18 |
| Weight | 1.270087g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
DG429DJ-E3 Overview
Presented in 18-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. High reliability is ensured by the advanced packaging method Tube. Multiplexers like this are mounted in the Through Hole position. 4:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature around -40°C~85°C TA extended. Total terminations are 18. Due to its 4 channels, the electrical component produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. An injection of 18 pins is performed into the body of the electrical component. These analog multiplexers are built based on SP4T switching circuits. There are 2 circuits in this switch device. Try searching with DG429 to find analog multiplexer variants. This digital multiplexer has 150Ohm internal resistance. Please refer to the datasheets for 18 pins functions. normally, users should not supply switches with voltages higher than 36V. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended to use 13V as the lowest voltage for the electrical part. For this multiplexer to operate, 20μA current would be sufficient. It may damage the digital multiplexer if the voltage is higher than 100μA. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. A dual power supply should have at least 7V voltage attached. Among the inputs that can be operated are the 8 inputs.
DG429DJ-E3 Features
4 Channels
Switch Circuit: SP4T
20μA Supply Current
DG429DJ-E3 Applications
There are a lot of Vishay Siliconix DG429DJ-E3 Analog Switches & Multiplexers ICs applications.
- SONET
- New designs requiring multiplexer functions
- Audio and video signal routing
- Fiber to the Home
- PCMCIA cards
- T1/E1 Terminals
- Residential Gateways, Home Gateway/Router
- E1 Network Equipment
- Industrial control systems
- Communication systems
